Argus A2 Instruções de Operação descarregar pdf (Página 5)

● General

In the following the device will be referred to as the

movement detector.

The movement block will only switch off when there is

no more movement in front of the device - in other

words, independently of the brightness.

The ETS application includes 5 independent

movement blocks, each with 4 output objects.

Note:

All of the settings described refer to ETS version

3, but you can also use all the settings and

functions with ETS version 2.

The application files (vd2 and vd3) are

configured in such a way that the application

loading time is considerably reduced. When you

convert an ETS 2 project to ETS 3, you lose this

time saving. If you are working with ETS 3, use

the vd3 files.

Total possible addresses and connections:

254 addresses; 255 connections

Note:

If you switch back to the preset values in either

ETS 2 or ETS 3 (by clicking "Standard"), all the

values that you have changed so far will be

deleted. Any group addresses which have been

parametrised will be lost.

Note:

Due to the fact that various functions depend

on other functions, these dependent functions

will not be visible and selectable in the ETS

unless the preceding function has been

enabled. If you de-select functions or change

parameters, group addresses that have already

been connected may be removed.

● Getting started quickly

When you insert the application in the ETS or click on

the "Standard" button, the ETS application will switch

automatically to minimum configuration.

In minimum configuration, it is possible to put the

presence detector into operation. For some

application cases, the minimum configuration is even

adequate for practical use. We also recommend

opening minimum configuration as a way of

familiarising yourself with the application software for

the presence detector. Here all of the extended or

more complex parameters are disabled. In "Block

configuration" only the first "Movement" block is

enabled for use. In the "Telegrams" tab only output

object 1 is enabled. This is a 1-bit output object. At the

start of movement this object sends a 1 telegram and

when the internal staircase timer has elapsed it sends

a 0 telegram. Each parameter can always be tuned to

its individual requirements. The brightness threshold

and the staircase timer always need to be adjusted to

suit requirements. Check the "Brightness" and "Times"

tabs.

In this way the corresponding objects are connected

to a KNX switch actuator.

To familiarise yourself with the extended and more

complex parameters see the following pages.

● General functions

The common safety pause

The application has a common safety pause system -

in other words, a safety pause triggered by the

movement detector will affect all blocks in the

application. As specified in a parameter the safety

pause can be triggered at the status feedback object

(safety pause) when there is an OFF telegram or when

there is an OFF and ON telegram.

The status feedback object of the switching/dimming

actuator must be connected to the feedback safety

pause object of the movement detector.

Once a safety pause has been started, signals from

the movement sensor will no longer be evaluated for

this period of time. An elapsed staircase timer cannot

be started by a movement during an active safety

pause and an ongoing staircase timer cannot be

retriggered by a movement.

An ongoing staircase timer is not affected by a safety

pause being activated. In other words, the staircase

timer will run through in the usual way.

Note:

Optical feedback can only be avoided by

selecting the right installation location for the

movement detector and the lighting. The safety

pause system and the safety pause object of

the application cannot compensate for all

planning mistakes.

Communication objects

You can select the following communication objects:

General:

Movement/monitoring 1307/1.0

Function Object name Type Prio Flags Behaviour

Safety

pause

Status feedback

object

1 bit Low WC Receive

1/1/1

1/1/2

Switch object

Status feedback obj.

Switch

Actuator

Status feedback obj.

Safety pause

Movement

Detector

Switch object

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comentários a estes Manuais

Sem comentários

Argus A2 Instruções de Operação Página 5

Comentários a estes Manuais

Manuais e produtos relacionados com Câmaras bridge Argus A2